- 您现在的位置：买卖IC网 > Sheet目录1228 > MAX4948EVKIT+ (Maxim Integrated Products)KIT EVAL FOR MAX4948
MAX4948 Evaluation Kit
Component Suppliers
SUPPLIER
Murata Mfg. Co., Ltd.
TDK Corp.
PHONE
770-436-1300
847-803-6100
WEBSITE
www.murata.com
www.component.tdk.com
Note: Indicate that you are using the MAX4948 when contacting these component suppliers.
Quick Start
Recommended Equipment
Before beginning, the following equipment is needed:
? SD card reader/SD card slot
? Computer with Windows ? 98SE/2000/XP/Vista oper-
ating system
Note: The MAX4948 EV kit does not require a driver or
software. The EV kit acts only as an SPDT switch, con-
necting one of two SD memory cards to the host’s SD
bus.
Procedure
The MAX4948 EV kit is fully assembled and tested.
Follow the steps below to verify board operation:
into the PCB and conforms to the dimensional stan-
dards of a thin SD memory card. The net effect is the
ability to switch between two SD memory cards on a
single SD bus.
Enable and Configuration
The EV kit is configured through jumpers JU1 and JU2.
Jumper JU2 is used to enable/disable the MAX4948
analog switches and jumper JU1 is used to switch
between the two SD card sockets, P1 and P2.
Enable (JU2)
The MAX4948 analog switch is enabled and disabled
through jumper JU2. See Table 1 for jumper JU2 functions.
Table 1. Jumper JU2 Functions
1) Verify that shunts are installed between each odd-and-
even pin of header J1 (i.e., between pins 1 and 2,
pins 3 and 4, etc.).
2) Verify that shunts are installed between each odd-and-
SHUNT
POSITION
1-2
EN PIN
Connected to VDD
DESCRIPTION
All switches are in a
high-impedance state.
even pin of header J2 (i.e., between pins 1 and 2,
pins 3 and 4, etc.).
3) Verify that a shunt is installed across pins 1-2 of
2-3* Connected to GND
*Default position.
All switches are on.
header JU1. This connects the NO_ inputs (from
socket P1) to the COM outputs.
4) Verify that a shunt is installed across pins 1-2 of
header JU2. This powers on the analog switches.
5) Insert the SD PCB plug (P3) into the SD card read-
er/SD card slot.
6) Verify that LED1 is illuminated.
Detailed Description
The MAX4948 evaluation kit (EV kit) evaluates the
Configuration (JU1)
Based on jumper JU1’s configuration, the signal lines
from one of the SD card sockets (P1 or P2) are connect-
ed to the common (COM) terminals of the analog switch-
es (COM1–COM6). The COM1–COM6 terminals are then
routed through header J2 to the SD PCB plug (P3). See
Table 2 for configuration options and Figure 1 for an
illustration of the MAX4948 analog switch connections.
Table 2. MAX4948 Configuration
MAX4948 hex SPDT data switch. The EV kit is
designed for an SD application, providing two SD sock-
ets and a single SD plug. Standard and thin SD memo-
ry cards can be inserted into the P1 and P2 sockets.
The MAX4948 is then used to switch between the two
SD memory cards, connecting one of the cards to the
SD plug. The SD plug can be inserted into any stan-
dard SD memory card slot. The SD plug is designed
CB PIN
(JU1)
VDD (1-2)*
GND (2-3)
COM_ TERMINAL
Connected to NO_
terminal
Connected to NC_
terminal
CONFIGURATION
SD card socket (P1)
connected to the SD card
plug (P3)
SD card socket (P2)
connected to the SD card
plug (P3)
Windows is a registered trademark of Microsoft Corp.
*Default position.
2
_______________________________________________________________________________________
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MAX4983EEVKIT+
KIT EVAL FOR MAX4983
MAX4989EVKIT+
EVALUATION KIT FOR MAX4989
MAX5079EVKIT
EVAL KIT FOR MAX5079
MAX5432EVKIT+
KIT EVAL FOR MAX5432
MAX5474EVKIT+
KIT EVAL FOR MAX5474
MAX5488EVKIT#
KIT EVALUATION FOR MAX5488
MAX5498EVKIT+
KIT EVAL FOR MAX5498
MAX5946LEVKIT
EVAL KIT FOR MAX5946
相关代理商/技术参数
MAX4949ELA+T
功能描述:电流和电力监控器、调节器 Overvoltage-Protect Controller RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel
MAX494CPD
功能描述:运算放大器 - 运放 uPower Single-Supply Rail-Rail RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel
MAX494CPD+
功能描述:运算放大器 - 运放 uPower Single-Supply Rail-Rail RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel
MAX494CSD
功能描述:运算放大器 - 运放 uPower Single-Supply Rail-Rail RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel
MAX494CSD+
功能描述:运算放大器 - 运放 uPower Single-Supply Rail-Rail RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel
MAX494CSD+T
功能描述:运算放大器 - 运放 uPower Single-Supply Rail-Rail RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel
MAX494CSD-T
功能描述:运算放大器 - 运放 uPower Single-Supply Rail-Rail RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel
MAX494EPD
功能描述:运算放大器 - 运放 RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel